Showing results: 616 - 628 of 628 items found.
-
ProView -
Innovative Control Systems, Inc.
ProView is a low cost, ARINC 664 bus reader / logger / analyzer designed specifically for the Rockwell-Collins specific ARINC 664 implementation that works well, is very low cost, and no external capture hardware is required. Innovative Control Systems, Inc. is pleased to announce the release of our new ARINC 664 ProView logging analyzer software which allows you to perform live display, recording, playback, and Export (to CSV file) of Rockwell Collins specific ARINC 664 data on a suitable Microsoft® Windows® operating system based laptop or PC. No additional capture hardware is required for this analyzer, just an available Ethernet port on the computer and you are able to analyze your data. The software can also be used to create configuration files for our FTSIU flight test data acquisition interfaces as well as playback flight test data sets recorded by that equipment.
-
Acces I/O Products, Inc.
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
PQM-711 -
Sonel S.A.
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
Fieldpiece Instruments, Inc
The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.
-
LISST-Portable|XR -
Sequoia Scientific, Inc.
Truly portable – completely self-contained with built-in data logger, processor, rechargeable battery, and 7” color touch screen display.Particle Size Range 0.35 to 500 micronsPumped and recirculating mixing chamber that keeps large and heavy particles suspended.Shock mounted optics block that can withstand the rigors of field use.A built-in ultrasonic probe for complete sample dispersion.Touch panel allows for easy SOP programming, sample analysis and display of data without a PC.Multiple Mie models as well as Fraunhofer model available for inversion, selectable from the touch panelAll data-processing is performed on board and stored in ASCII format. No post-processing necessary.Outputs: Total volume concentration, mean size, standard deviation, optical transmission, D5, D10, D16, D25, D50 (median grain size), D60, D75, D84, D90, D95, D60/D10 (Hazen uniformity coefficient), particle surface area, silt fraction, silt volume, size distribution, battery voltage, sample notes.Based on the laser diffraction principle. Compliant with ISO-13320-1 standard.
-
MVX -
Dakota Ultrasonics
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
PCE Instruments
A light meter is a very sensitive electronic measuring device used to help monitor the illumination of any given area. Most light meter devices are small in size, simple to operate and equipped with an easy-to-read lighted screen made of special glass. Typically, a heavy-duty housing protects the light sensor inside the light meter from damage. A light meter is used for measuring brightness in lux (lx), foot candle (fc) or candela per square meter (cd/m²)measuring units. Some light meter devices are equipped with an internal memory or data logger to record and save measurements. The measurement of light intensity with a light meter is becoming increasingly important in the workplace due to safety concerns. Light measurement is also necessary to determine the best location and angle when installing and adjusting solar panels.
-
EL30000 Series -
Keysight Technologies
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
N6705C -
Keysight Technologies
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
Hawk Radius® -
International Medcom
The Hawk® Radius is a ruggedized solution for monitoring both ambient and elevated levels of ionizing radiation. Like a Hawk with its remarkable vision, the Hawk Radius Probe “sees” things that other probes cannot. The high sensitivity weatherized pancake sensor can provide early warning of changing ambient radiation conditions, while the energy compensated detector can accurately report penetrating gamma radiation dose rate at elevated levels. Radius probes are typically deployed as part of an environmental radiation monitoring program, or for safety and security systems. In its standard configuration the probe detects beta, low energy gamma and x-radiation with one channel and energy compensated penetrating gamma radiation levels with a second channel. It can be configured to detect alpha radiation as well. The Hawk® Radius has been deployed worldwide in demanding conditions for protecting communities and collecting environmental radiation data. It can be deployed easily and requires minimum maintenance. The Radius is compatible with Medcomʻs GeigerLink adapter and the IMI Gateway App for use with personal computers. It can also be used with most data loggers including popular Campbell Scientific models.
-
PeakTech Prüf- und Messtechnik GmbH
An innovative graphic multimeter with a 50,000-digit color TFT display for precise measurements with a high DC basic accuracy of 0.05%. The internal data logger enables the recording of measured values, which can be recorded over a period of several hours and the transfer to a Windows PC at a later time is ensured. Internally stored measured value recordings can also be accessed and graphically displayed on the multimeter itself or on the PC. Via Bluetooth, the measured values can also be displayed live via app for Android and iOS devices, recorded in a table and e.g. send by email for further processing. This multimeter has a variety of measurement functions for direct and alternating voltage measurements (incl.ACV + DCV), direct and alternating current measurements, resistance, capacitance, frequency or temperature, whereby alternating voltage and alternating current are recorded as True RMS values. Due to the extensive measurement functions and the intuitive operation, this device is ideally suited for every electronics engineer, technician and engineer who attach great importance to a precise, indestructible and technically powerful multimeter.
-
GAO Tek Inc.
GAOTek offers high quality, affordable, secure and accurate Ultrasonic Flow Meters for sale to the United States, Canada and globally. Ultrasonic Flow Meters often have a sending and a receiving transducer for measuring the velocity of fluids to accurately calculate the flow of volume in a pipe by using sound waves, acoustic waves or vibrations with a frequency of >20 KHz. GAOTek offers a variety of top-notch Ultrasonic Flow Meters designed for different environments, from wide pipes to an all liquid environment, such as sea water, oil, sewage, alcohol, et al. GAOTek’s easy to use Ultrasonic Flow Meters come with a built-in printer and a built-in data logger. They provide accurate readings and have an accuracy rate of ±1% at rates greater than 0.2mps. They also offer multi-language menu selections, long lasting battery life for continuous usage, large LCD screens, and a huge storage.
-
KB Series -
Darwin Chambers Company
Darwin Chambers KB series Environmental Chambers are a top selling unit. It is quiet, easy to clean, highly reliable and ideal for laboratory use. Our environmental chamber offers hot gas bypass control of refrigeration and resistive heat to facilitate reliable, critical temperature and humidity control. All KB series environmental testing chamber models are designed to have a temperature range of 4-60o Celsius. Temperatures greater than 60o Celsius or lower than 4o Celsius can be achieved with optional upgrades to construction and components. All KB series environmental chambers come standard with Fuji’s PXG4 microprocessor, but we often install Watlow brand microprocessors for customers that need that brand or the capabilities it has. Unlike many proprietary controllers on the market, these controllers are available off the shelf and have been proven in tens of thousands of installations. All necessary functions are included in our Features section below. Many additional options are available both regarding control and recording of data (chart recorders and loggers)
